* means they must be defined before operator {}.
*/
privset "local_op" {
- privs = oper:local_kill, oper:operwall;
+ privs = oper:general, oper:local_kill, oper:operwall;
};
privset "server_bot" {
autochanmodes = "+nt";
displayed_usercount = 3;
strip_topic_colors = no;
+ opmod_send_statusmsg = no;
};
serverhide {
disable_hidden = no;
};
-/* These are the blacklist settings.
+/* These are the DNSBL settings.
* You can have multiple combinations of host and rejection reasons.
* They are used in pairs of one host/rejection reason.
*
- * These settings should be adequate for most networks.
+ * The default settings should be adequate for most networks.
*
- * Word to the wise: Do not use blacklists like SPEWS for blocking IRC
- * connections.
+ * It is not recommended to use DNSBL services designed for e-mail spam
+ * prevention, such as SPEWS for blocking IRC connections.
*
* As of charybdis 2.2, you can do some keyword substitution on the rejection
* reason. The available keyword substitutions are:
* is considered a match. If included, a comma-separated list of *quoted*
* strings is allowed to match queries. They may be of the format "0" to "255"
* to match the final octet (e.g. 127.0.0.1) or "127.x.y.z" to explicitly match
- * an A record. The blacklist is only applied if it matches anything in the
+ * an A record. The DNSBL match is only applied if it matches anything in the
* list. You may freely mix full IP's and final octets.
*
- * Consult your blacklist provider for the meaning of these parameters; they
- * are usually used to denote different ban types.
+ * Consult your DNSBL provider for the meaning of these parameters; they
+ * are usually used to denote different block reasons.
*/
-blacklist {
+dnsbl {
host = "rbl.efnetrbl.org";
type = ipv4;
reject_reason = "${nick}, your IP (${ip}) is listed in EFnet's RBL. For assistance, see http://efnetrbl.org/?i=${ip}";
* WARNING:
* These settings are considered experimental. Only the most common proxy types
* are checked for (Charybdis is immune from POST and GET proxies). If you are
- * not comfortable with experimental code, remove or comment out the *entire*
- * block below to disable the proxy scanner.
+ * not comfortable with experimental code, do not use this feature.
*/
-opm {
+#opm {
/* IPv4 address to listen on. This must be a publicly facing IP address
* to be effective.
* If omitted, it defaults to serverinfo::vhost.
/* IPv4 port to listen on.
* This should not be the same as any existing listeners.
*/
- #port_ipv4 = 32000;
+ #port_v4 = 32000;
/* IPv6 address to listen on. This must be a publicly facing IP address
* to be effective.
/* IPv6 port to listen on.
* This should not be the same as any existing listeners.
*/
- #port_ipv6 = 32000;
+ #port_v6 = 32000;
/* You can also set the listen_port directive which will set both the
* IPv4 and IPv6 ports at once.
*/
- listen_port = 32000;
+ #listen_port = 32000;
/* This sets the timeout in seconds before ending open proxy scans.
* Values less than 1 or greater than 60 are ignored.
* It is advisable to keep it as short as feasible, so clients do not
* get held up by excessively long scan times.
*/
- timeout = 5;
+ #timeout = 5;
/* These are the ports to scan for SOCKS4 proxies on. They may overlap
* with other scan types. Sensible defaults are given below.
*/
- socks4_ports = 1080, 10800, 443, 80, 8080, 8000;
+ #socks4_ports = 1080, 10800, 443, 80, 8080, 8000;
/* These are the ports to scan for SOCKS5 proxies on. They may overlap
* with other scan types. Sensible defaults are given below.
*/
- socks5_ports = 1080, 10800, 443, 80, 8080, 8000;
+ #socks5_ports = 1080, 10800, 443, 80, 8080, 8000;
/* These are the ports to scan for HTTP connect proxies on (plaintext).
* They may overlap with other scan types. Sensible defaults are given
* below.
*/
- httpconnect_ports = 80, 8080, 8000;
+ #httpconnect_ports = 80, 8080, 8000;
/* These are the ports to scan for HTTPS CONNECT proxies on (SSL).
* They may overlap with other scan types. Sensible defaults are given
* below.
*/
- httpsconnect_ports = 443, 4443;
-};
+ #httpsconnect_ports = 443, 4443;
+#};
alias "NickServ" {
target = "NickServ";
resv_fnc = yes;
global_snotices = yes;
dline_with_reason = yes;
- kline_delay = 0 seconds;
kline_with_reason = yes;
+ hide_tkdline_duration = no;
kline_reason = "K-Lined";
identify_service = "NickServ@services.int";
identify_command = "IDENTIFY";
no_oper_flood = yes;
max_targets = 4;
client_flood_max_lines = 20;
+ post_registration_delay = 0 seconds;
use_whois_actually = no;
oper_only_umodes = operwall, locops, servnotice;
oper_umodes = locops, servnotice, operwall, wallop;
away_interval = 30;
certfp_method = spki_sha256;
hide_opers_in_whois = no;
+ tls_ciphers_oper_only = no;
};
modules {