#loadmodule "extensions/m_extendchans";
#loadmodule "extensions/m_findforwards";
#loadmodule "extensions/m_identify";
+#loadmodule "extensions/m_locops";
#loadmodule "extensions/no_oper_invis";
#loadmodule "extensions/sno_farconnect";
#loadmodule "extensions/sno_globalkline";
* encrypted | password is encrypted with mkpasswd
* spoof_notice | give a notice when spoofing hosts
* exceed_limit (old > flag) | allow user to exceed class user limits
- * kline_exempt (old ^ flag) | exempt this user from k/g/xlines&dnsbls
- * dnsbl_exempt | exempt this user from dnsbls
- * spambot_exempt | exempt this user from spambot checks
- * shide_exempt | exempt this user from serverhiding
+ * kline_exempt (old ^ flag) | exempt this user from k/g/xlines,
+ * | dnsbls, and proxies
+ * proxy_exempt | exempt this user from proxies
+ * dnsbl_exempt | exempt this user from dnsbls
+ * spambot_exempt | exempt this user from spambot checks
+ * shide_exempt | exempt this user from serverhiding
* jupe_exempt | exempt this user from generating
* warnings joining juped channels
- * resv_exempt | exempt this user from resvs
+ * resv_exempt | exempt this user from resvs
* flood_exempt | exempt this user from flood limits
- * USE WITH CAUTION.
+ * USE WITH CAUTION.
* no_tilde (old - flag) | don't prefix ~ to username if no ident
* need_ident (old + flag) | require ident for user in this class
* need_ssl | require SSL/TLS for user in this class
flags = compressed, topicburst;
#fingerprint = "c77106576abf7f9f90cca0f63874a60f2e40a64b";
-
- /* If the connection is IPv6, uncomment below.
- * Use 0::1, not ::1, for IPv6 localhost. */
- #aftype = ipv6;
};
connect "ssl.uplink.com" {
* You can have multiple combinations of host and rejection reasons.
* They are used in pairs of one host/rejection reason.
*
- * These settings should be adequate for most networks, and are (presently)
- * required for use on StaticBox.
+ * These settings should be adequate for most networks.
*
* Word to the wise: Do not use blacklists like SPEWS for blocking IRC
* connections.
# reject_reason = "${nick}, your IP (${ip}) is listed in ${dnsbl-host} for some reason. In order to protect ${network-name} from abuse, we are not allowing connections listed in ${dnsbl-host} to connect";
};
+/* These are the OPM settings.
+ * This is similar to the functionality provided by BOPM. It will scan incoming
+ * connections for open proxies by connecting to clients and attempting several
+ * different open proxy handshakes. If they connect back to us (via a dedicated
+ * listening port), and send back the data we send them, they are considered
+ * an open proxy. For politeness reasons (users may be confused by the incoming
+ * connection attempts if they are logging incoming connections), the user is
+ * notified upon connect if they are being scanned.
+ *
+ * WARNING:
+ * These settings are considered experimental. Only the most common proxy types
+ * are checked for (Charybdis is immune from POST and GET proxies). If you are
+ * not comfortable with experimental code, remove or comment out the *entire*
+ * block below to disable the proxy scanner.
+ */
+opm {
+ /* IPv4 address to listen on. This must be a publicly facing IP address
+ * to be effective.
+ * If omitted, it defaults to serverinfo::vhost.
+ */
+ #listen_ipv4 = "127.0.0.1";
+
+ /* IPv4 port to listen on.
+ * This should not be the same as any existing listeners.
+ */
+ #port_ipv4 = 32000;
+
+ /* IPv6 address to listen on. This must be a publicly facing IP address
+ * to be effective.
+ * If omitted, it defaults to serverinfo::vhost6.
+ */
+ #listen_ipv6 = "::1";
+
+ /* IPv6 port to listen on.
+ * This should not be the same as any existing listeners.
+ */
+ #port_ipv6 = 32000;
+
+ /* You can also set the listen_port directive which will set both the
+ * IPv4 and IPv6 ports at once.
+ */
+ listen_port = 32000;
+
+ /* This sets the timeout in seconds before ending open proxy scans.
+ * Values less than 1 or greater than 60 are ignored.
+ * It is advisable to keep it as short as feasible, so clients do not
+ * get held up by excessively long scan times.
+ */
+ timeout = 5;
+
+ /* These are the ports to scan for SOCKS4 proxies on. They may overlap
+ * with other scan types. Sensible defaults are given below.
+ */
+ socks4_ports = 1080, 10800, 443, 80, 8080, 8000;
+
+ /* These are the ports to scan for SOCKS5 proxies on. They may overlap
+ * with other scan types. Sensible defaults are given below.
+ */
+ socks5_ports = 1080, 10800, 443, 80, 8080, 8000;
+
+ /* These are the ports to scan for HTTP connect proxies on (plaintext).
+ * They may overlap with other scan types. Sensible defaults are given
+ * below.
+ */
+ httpconnect_ports = 80, 8080, 8000;
+
+ /* These are the ports to scan for HTTPS CONNECT proxies on (SSL).
+ * They may overlap with other scan types. Sensible defaults are given
+ * below.
+ */
+ httpsconnect_ports = 443, 4443;
+};
+
alias "NickServ" {
target = "NickServ";
};
tkline_expire_notices = no;
default_floodcount = 10;
failed_oper_notice = yes;
- dots_in_ident=2;
+ dots_in_ident = 2;
min_nonwildcard = 4;
min_nonwildcard_simple = 3;
max_accept = 100;
warn_no_nline = yes;
use_propagated_bans = yes;
stats_e_disabled = no;
- stats_c_oper_only=no;
- stats_h_oper_only=no;
- stats_y_oper_only=no;
- stats_o_oper_only=yes;
- stats_P_oper_only=no;
- stats_i_oper_only=masked;
- stats_k_oper_only=masked;
+ stats_c_oper_only = no;
+ stats_h_oper_only = no;
+ stats_y_oper_only = no;
+ stats_o_oper_only = yes;
+ stats_P_oper_only = no;
+ stats_i_oper_only = masked;
+ stats_k_oper_only = masked;
map_oper_only = no;
operspy_admin_only = no;
operspy_dont_care_user_info = no;
throttle_count = 4;
max_ratelimit_tokens = 30;
away_interval = 30;
- certfp_method = sha1;
+ certfp_method = spki_sha256;
hide_opers_in_whois = no;
};