* Account bans (+b $a[:mask]) -- extb_account.so
* Banned from another channel (+b $j:mask) -- extb_canjoin.so
* Other-channel bans (+b $c:mask) -- extb_channel.so
+ * Combination extbans -- extb_combi.so
* Extended ban (+b $x:mask) -- extb_extgecos.so
+ * Hostmask bans (for combination extbans) -- extb_hostmask.so
* Oper bans (+b $o) -- extb_oper.so
* Realname (gecos) bans (+b $r:mask) -- extb_realname.so
* Server bans (+b $s:mask) -- extb_server.so
* Remote oper up notices -- sno_globaloper.so
* /whois notifications (snomask +W) -- sno_whois.so
* Oper-override (modehacking only) -- override.so
+ * Stop services kills -- no_kill_services.so
*/
#loadmodule "extensions/chm_adminonly.so";
#loadmodule "extensions/chm_operonly.so";
#loadmodule "extensions/extb_account.so";
#loadmodule "extensions/extb_canjoin.so";
#loadmodule "extensions/extb_channel.so";
+#loadmodule "extensions/extb_combi.so";
#loadmodule "extensions/extb_extgecos.so";
+#loadmodule "extensions/extb_hostmask.so";
#loadmodule "extensions/extb_oper.so";
#loadmodule "extensions/extb_realname.so";
#loadmodule "extensions/extb_server.so";
#loadmodule "extensions/sno_globaloper.so";
#loadmodule "extensions/sno_whois.so";
#loadmodule "extensions/override.so";
-
+#loadmodule "extensions/no_kill_services.so";
+
/* serverinfo {}: Contains information about the server. (OLD M:) */
serverinfo {
/* name: the name of our server */
* is on. Shown in the 005 reply and used with serverhiding.
*/
network_name = "MyNet";
- network_desc = "This is My Network";
/* hub: allow this server to act as a hub and have multiple servers
* connected to it.
/* vhost: the IP to bind to when we connect outward to ipv4 servers.
* This should be an ipv4 IP only.
*/
- #vhost = "192.169.0.1";
+ #vhost = "192.0.2.6";
/* vhost6: the IP to bind to when we connect outward to ipv6 servers.
* This should be an ipv6 IP only.
*/
- #vhost6 = "3ffe:80e8:546::2";
+ #vhost6 = "2001:db7:2::6";
/* ssl_private_key: our ssl private key */
ssl_private_key = "etc/ssl.key";
/* ssl_cert: certificate for our ssl server */
- ssl_cert = "etc/ssl.cert";
+ ssl_cert = "etc/ssl.pem";
/* ssl_dh_params: DH parameters, generate with openssl dhparam -out dh.pem 1024 */
ssl_dh_params = "etc/dh.pem";
+ /* ssl_cipher_list: A list of ciphers, dependent on your TLS backend */
+ #ssl_cipher_list = "EECDH+HIGH:EDH+HIGH:HIGH:!aNULL";
+
/* ssld_count: number of ssld processes you want to start, if you
* have a really busy server, using N-1 where N is the number of
* cpu/cpu cores you have might be useful. A number greater than one
/* host: set a specific IP/host the ports after the line will listen
* on. This may be ipv4 or ipv6.
*/
- host = "1.2.3.4";
+ host = "192.0.2.6";
port = 7000, 7001;
sslport = 9000, 9001;
- host = "3ffe:1234:a:b:c::d";
+ host = "2001:db8:2::6";
port = 7002;
sslport = 9002;
};
* prepending a 0 if it starts with a colon) and can also use CIDR
* masks.
*/
- user = "*@172.16.0.0/12";
- user = "*test@123D:B567:*";
+ user = "*@198.51.100.0/24";
+ user = "*test@2001:db8:1:*";
+
+ /* auth_user: This allows specifying a username:password instead of
+ * just a password in PASS, so that a fixed user@host is not
+ * necessary for a specific auth{} block.
+ */
+ #auth_user = "SomeUser";
/* password: an optional password that is required to use this block.
* By default this is not encrypted, specify the flag "encrypted" in
* not have to obey the redirection, the ircd just suggests to them
* an alternative server.
*/
- redirserv = "irc.some.domain";
+ redirserv = "irc.example.net";
redirport = 6667;
- user = "*.some.domain";
+ user = "*.example.com";
/* class: a class is required even though it is not used */
class = "users";
/* host: the host or IP to connect to. If a hostname is used it
* must match the reverse dns of the server.
*/
- host = "192.168.0.1";
+ host = "203.0.113.3";
/* vhost: the host or IP to bind to for this connection. If this
* is not specified, the default vhost (in serverinfo {}) is used.
*/
- #vhost = "192.168.0.50";
+ #vhost = "192.0.2.131";
/* passwords: the passwords we send (OLD C:) and accept (OLD N:).
* The remote server will have these passwords reversed.
* if applicable. Addresses starting with a colon get an extra
* zero prepended, for example: 0::1
*/
- host = "3ffd:dead:beef::1";
+ host = "2001:db8:3::8";
send_password = "password";
accept_password = "password";
port = 6666;
/* Example of ssl server-to-server connection, ssl flag doesn't need
* compressed flag, 'cause it uses own compression
*/
- host = "192.168.0.1";
+ host = "203.0.113.129";
send_password = "password";
accept_password = "anotherpassword";
port = 9999;
/* exempt {}: IPs that are exempt from Dlines and rejectcache. (OLD d:) */
exempt {
- ip = "192.168.0.0/16";
+ ip = "192.0.2.0/24";
/* these may be stacked */
ip = "127.0.0.1";
- ip = "10.0.0.0/8";
};
/* The channel block contains options pertaining to channels */
* supported.
*/
disable_local_channels = no;
+
+ /* autochanmodes: the channel modes that should be automatically set
+ * when a channel is created.
+ */
+ autochanmodes = "+nt";
};
* IPv4 is currently the default as few blacklists support IPv6 operation
* as of this writing.
*
- * Note: AHBL (the providers of the below *.ahbl.org BLs) request that they be
- * contacted, via email, at admins@2mbit.com before using these BLs.
- * See <http://www.ahbl.org/services.php> for more information.
+ * As of charybdis 3.5, a matches parameter is allowed; if omitted, any result
+ * is considered a match. If included, a comma-separated list of *quoted*
+ * strings is allowed to match queries. They may be of the format "0" to "255"
+ * to match the final octet (e.g. 127.0.0.1) or "127.x.y.z" to explicitly match
+ * an A record. The blacklist is only applied if it matches anything in the
+ * list. You may freely mix full IP's and final octets.
+ *
+ * Consult your blacklist provider for the meaning of these parameters; they
+ * are usually used to denote different ban types.
*/
blacklist {
host = "rbl.efnetrbl.org";
type = ipv4;
reject_reason = "${nick}, your IP (${ip}) is listed in EFnet's RBL. For assistance, see http://efnetrbl.org/?i=${ip}";
-# host = "ircbl.ahbl.org";
-# type = ipv4;
-# reject_reason = "${nick}, your IP (${ip}) is listed in ${dnsbl-host} for having an open proxy. In order to protect ${network-name} from abuse, we are not allowing connections with open proxies to connect.";
-#
-# host = "tor.ahbl.org";
-# type = ipv4;
-# reject_reason = "${nick}, your IP (${ip}) is listed as a TOR exit node. In order to protect ${network-name} from tor-based abuse, we are not allowing TOR exit nodes to connect to our network.";
-#
- /* Example of a blacklist that supports both IPv4 and IPv6 */
+ /* Example of a blacklist that supports both IPv4 and IPv6 and using matches */
# host = "foobl.blacklist.invalid";
+# matches = "4", "6", "127.0.0.10";
# type = ipv4, ipv6;
# reject_reason = "${nick}, your IP (${ip}) is listed in ${dnsbl-host} for some reason. In order to protect ${network-name} from abuse, we are not allowing connections listed in ${dnsbl-host} to connect";
};
* If disabled, local opers can see them.
* Dynamic spoofs (e.g. set by services) are unaffected by this;
* any oper (local and remote) can see the real ip.
- * Warning: for whowas, this is checked when the client exits,
- * not when the IP is shown.
*/
hide_spoof_ips = yes;
*/
servicestring = "is a Network Service";
+ /*
+ * Nick of the network's SASL agent. Used to check whether services are here,
+ * SASL credentials are only sent to its server. Needs to be a service.
+ *
+ * Defaults to SaslServ if unspecified.
+ */
+ sasl_service = "SaslServ";
+
/* disable fake channels: disable local users joining fake versions
* of channels, eg #foo^B^B. Disables bold, mirc colour, reverse,
* underline and hard space. (ASCII 2, 3, 22, 31, 160 respectively).
ts_warn_delta = 30 seconds;
ts_max_delta = 5 minutes;
- /* client exit: prepend a users quit message with "Client exit: " */
+ /* client exit: prepend a user's quit message with "Quit: " */
client_exit = yes;
/* collision fnc: change user's nick to their UID instead of
* provided they have umode +s set */
oper_snomask = "+s";
- /* use egd: if your system does not have *random devices yet you
- * want to use OpenSSL and encrypted links, enable this. Beware -
- * EGD is *very* CPU intensive when gathering data for its pool
- */
- #use_egd = yes;
-
- /* egdpool path: path to EGD pool. Not necessary for OpenSSL >= 0.9.7
- * which automatically finds the path.
- */
- #egdpool_path = "/var/run/egd-pool";
-
-
/* compression level: level of compression for compressed links between
* servers.
*
* counts.
*/
away_interval = 30;
+
+ /* certfp_method: the method that should be used for computing certificate fingerprints.
+ * Acceptable options are sha1, sha256 and sha512. Networks running versions of charybdis
+ * prior to charybdis 3.5 MUST use sha1 for certfp_method.
+ */
+ certfp_method = sha1;
};
modules {
projects / solanum.git / blobdiff