*
* Times/durations are written as:
* 12 hours 30 minutes 1 second
- *
+ *
* Valid units of time:
* month, week, day, hour, minute, second
*
* Valid units of size:
* megabyte/mbyte/mb, kilobyte/kbyte/kb, byte
*
- * Sizes and times may be singular or plural.
- */
+ * Sizes and times may be singular or plural.
+ */
/* Extensions:
*
* To use them, uncomment the lines below.
*
* Channel mode +-A (admin only) -- chm_adminonly
+ * Channel mode +-T (blocks notices) -- chm_nonotice
* Channel mode +-O (oper only) -- chm_operonly
* Channel mode +-S (ssl only) -- chm_sslonly
* Emulates channel mode +-O (oper only) (+-iI $o) -- chm_operonly_compat
* Realname (gecos) bans (+b $r:mask) -- extb_realname
* Server bans (+b $s:mask) -- extb_server
* SSL bans (+b $z) -- extb_ssl
+ * User mode bans (+b $u:modes) -- extb_usermode
* Helpops system (umode +H) -- helpops
* HURT system -- hurt
* New host mangling (umode +x) -- ip_cloaking_4.0
* Dynamically extend channel limits -- m_extendchans
* Find channel forwards -- m_findforwards
* /identify support -- m_identify
+ * /locops support -- m_locops
* Opers cannot be invisible (umode +i) -- no_oper_invis
* Far connection notices (snomask +F) -- sno_farconnect
* Remote k/d/x line active notices -- sno_globalkline
* Stop services kills -- no_kill_services
*/
#loadmodule "extensions/chm_adminonly";
+#loadmodule "extensions/chm_nonotice";
#loadmodule "extensions/chm_operonly";
#loadmodule "extensions/chm_sslonly";
#loadmodule "extensions/chm_operonly_compat";
#loadmodule "extensions/extb_realname";
#loadmodule "extensions/extb_server";
#loadmodule "extensions/extb_ssl";
+#loadmodule "extensions/extb_usermode";
#loadmodule "extensions/helpops";
#loadmodule "extensions/hurt";
#loadmodule "extensions/ip_cloaking_4.0";
#loadmodule "extensions/m_extendchans";
#loadmodule "extensions/m_findforwards";
#loadmodule "extensions/m_identify";
+#loadmodule "extensions/m_locops";
#loadmodule "extensions/no_oper_invis";
#loadmodule "extensions/sno_farconnect";
#loadmodule "extensions/sno_globalkline";
/* vhost6: the IP to bind to when we connect outward to ipv6 servers.
* This should be an ipv6 IP only.
*/
- #vhost6 = "2001:db7:2::6";
-
- /* ssl_private_key: our ssl private key */
- ssl_private_key = "etc/ssl.key";
+ #vhost6 = "2001:db8:2::6";
- /* ssl_cert: certificate for our ssl server */
+ /* ssl_cert: certificate (and optionally key) for our ssl server */
ssl_cert = "etc/ssl.pem";
- /* ssl_dh_params: DH parameters, generate with openssl dhparam -out dh.pem 1024 */
+ /* ssl_private_key: our ssl private key (if not contained in ssl_cert file) */
+ #ssl_private_key = "etc/ssl.key";
+
+ /* ssl_dh_params: DH parameters, generate with openssl dhparam -out dh.pem 2048 */
+ /* If you do not provide parameters, some TLS backends will fail on DHE- ciphers,
+ and some will succeed but use weak, common DH groups! */
ssl_dh_params = "etc/dh.pem";
/* ssl_cipher_list: A list of ciphers, dependent on your TLS backend */
*/
cidr_ipv6_bitlen = 64;
- /* number_per_cidr: Number of connections to allow from a subnet of the
+ /* number_per_cidr: Number of connections to allow from a subnet of the
* size given in cidr_ipv4_bitlen/cidr_ipv6_bitlen.
* 4 seems to be a good default to me.
*/
max_number = 1;
/* sendq: servers need a higher sendq as they are sent more data */
- sendq=2 megabytes;
+ sendq = 2 megabytes;
};
/* listen {}: contain information about the ports ircd listens on (OLD P:) */
/* port: the specific port to listen on. if no host is specified
* before, it will listen on all available IPs.
*
- * sslport: the specific port to listen ssl connections on. if no
+ * sslport: the specific port to listen ssl connections on. if no
* host is specified before, it will listen on all available IPs.
*
* ports are seperated via a comma, a range may be specified using ".."
*/
-
+
/* port: listen on all available IPs, ports 5000 and 6665 to 6669 */
port = 5000, 6665 .. 6669;
-
- /* sslport: listen for ssl connections on all available IPs, port 9999 */
- sslport = 9999;
- /* host: set a specific IP/host the ports after the line will listen
+ /* sslport: listen for ssl connections on all available IPs, port 6697 */
+ sslport = 6697;
+
+ /* host: set a specific IP/host the ports after the line will listen
* on. This may be ipv4 or ipv6.
*/
host = "192.0.2.6";
host = "2001:db8:2::6";
port = 7002;
sslport = 9002;
+
+ /* wsock: listeners defined with this option enabled will be websocket listeners,
+ * and will not accept normal clients.
+ */
+ wsock = yes;
+ sslport = 9999;
};
/* auth {}: allow users to connect to the ircd (OLD I:) */
* flags = ...; below if it is.
*/
password = "letmein";
-
+
/* spoof: fake the users user@host to be be this. You may either
* specify a host or a user@host to spoof to. This is free-form,
* just do everyone a favour and dont abuse it. (OLD I: = flag)
spoof = "I.still.hate.packets";
/* Possible flags in auth:
- *
+ *
* encrypted | password is encrypted with mkpasswd
* spoof_notice | give a notice when spoofing hosts
* exceed_limit (old > flag) | allow user to exceed class user limits
- * kline_exempt (old ^ flag) | exempt this user from k/g/xlines&dnsbls
+ * kline_exempt (old ^ flag) | exempt this user from k/g/xlines,
+ * | dnsbls, and proxies
* dnsbl_exempt | exempt this user from dnsbls
+ * proxy_exempt | exempt this user from proxies
* spambot_exempt | exempt this user from spambot checks
* shide_exempt | exempt this user from serverhiding
* jupe_exempt | exempt this user from generating
* extend_chans | allow this user to join more channels than normal
*/
flags = kline_exempt, exceed_limit;
-
+
/* class: the class the user is placed in */
class = "opers";
};
*/
redirserv = "irc.example.net";
redirport = 6667;
-
+
user = "*.example.com";
/* class: a class is required even though it is not used */
user = "*@127.0.0.1";
/* password: the password required to oper. Unless ~encrypted is
- * contained in flags = ...; this will need to be encrypted using
+ * contained in flags = ...; this will need to be encrypted using
* mkpasswd, MD5 is supported
*/
password = "etcnjl8juSU1E";
/* rsa key: the public key for this oper when using Challenge.
- * A password should not be defined when this is used, see
+ * A password should not be defined when this is used, see
* doc/challenge.txt for more information.
*/
#rsa_public_key_file = "/usr/local/ircd/etc/oper.pub";
send_password = "password";
accept_password = "anotherpassword";
- /* fingerprint: if specified, the server's client certificate
- * fingerprint will be checked against the specified fingerprint
- * below.
+ /* fingerprint: if flags = ssl is specified, the server's
+ * certificate fingerprint will be checked against the fingerprint
+ * specified below. required if using flags = ssl.
*/
#fingerprint = "c77106576abf7f9f90cca0f63874a60f2e40a64b";
* compressed - compress traffic via ziplinks
* topicburst - burst topics between servers
* ssl - ssl/tls encrypted server connections
+ * no-export - marks the link as a no-export link (not exported to other links)
*/
flags = compressed, topicburst;
};
connect "ipv6.lame.server" {
- /* Hosts that are IPv6 addresses must be in :: shortened form
- * if applicable. Addresses starting with a colon get an extra
- * zero prepended, for example: 0::1
- */
+ host = "192.0.2.1";
host = "2001:db8:3::8";
send_password = "password";
accept_password = "password";
port = 6666;
- /* aftype: controls whether the connection uses "ipv4" or "ipv6".
- * Default is ipv4.
+ /* aftype: controls whether the outgoing connection uses "ipv4" or "ipv6".
+ * Default is to try either at random.
*/
aftype = ipv6;
class = "server";
default_split_user_count = 0;
/* split servers: when the amount of servers that have acknowledged
- * theyve finished bursting is lower than this, consider ourselves
+ * theyve finished bursting is lower than this, consider ourselves
* split. this must be set for automatic splitmode
*/
default_split_server_count = 0;
* You can have multiple combinations of host and rejection reasons.
* They are used in pairs of one host/rejection reason.
*
- * These settings should be adequate for most networks, and are (presently)
- * required for use on StaticBox.
+ * These settings should be adequate for most networks.
*
* Word to the wise: Do not use blacklists like SPEWS for blocking IRC
* connections.
* to match the final octet (e.g. 127.0.0.1) or "127.x.y.z" to explicitly match
* an A record. The blacklist is only applied if it matches anything in the
* list. You may freely mix full IP's and final octets.
- *
+ *
* Consult your blacklist provider for the meaning of these parameters; they
* are usually used to denote different ban types.
*/
# reject_reason = "${nick}, your IP (${ip}) is listed in ${dnsbl-host} for some reason. In order to protect ${network-name} from abuse, we are not allowing connections listed in ${dnsbl-host} to connect";
};
+/* These are the OPM settings.
+ * This is similar to the functionality provided by BOPM. It will scan incoming
+ * connections for open proxies by connecting to clients and attempting several
+ * different open proxy handshakes. If they connect back to us (via a dedicated
+ * listening port), and send back the data we send them, they are considered
+ * an open proxy. For politeness reasons (users may be confused by the incoming
+ * connection attempts if they are logging incoming connections), the user is
+ * notified upon connect if they are being scanned.
+ *
+ * WARNING:
+ * These settings are considered experimental. Only the most common proxy types
+ * are checked for (Charybdis is immune from POST and GET proxies). If you are
+ * not comfortable with experimental code, do not use this feature.
+ */
+#opm {
+ /* IPv4 address to listen on. This must be a publicly facing IP address
+ * to be effective.
+ * If omitted, it defaults to serverinfo::vhost.
+ */
+ #listen_ipv4 = "127.0.0.1";
+
+ /* IPv4 port to listen on.
+ * This should not be the same as any existing listeners.
+ */
+ #port_v4 = 32000;
+
+ /* IPv6 address to listen on. This must be a publicly facing IP address
+ * to be effective.
+ * If omitted, it defaults to serverinfo::vhost6.
+ */
+ #listen_ipv6 = "::1";
+
+ /* IPv6 port to listen on.
+ * This should not be the same as any existing listeners.
+ */
+ #port_v6 = 32000;
+
+ /* You can also set the listen_port directive which will set both the
+ * IPv4 and IPv6 ports at once.
+ */
+ #listen_port = 32000;
+
+ /* This sets the timeout in seconds before ending open proxy scans.
+ * Values less than 1 or greater than 60 are ignored.
+ * It is advisable to keep it as short as feasible, so clients do not
+ * get held up by excessively long scan times.
+ */
+ #timeout = 5;
+
+ /* These are the ports to scan for SOCKS4 proxies on. They may overlap
+ * with other scan types. Sensible defaults are given below.
+ */
+ #socks4_ports = 80, 443, 1080, 8000, 8080, 10800;
+
+ /* These are the ports to scan for SOCKS5 proxies on. They may overlap
+ * with other scan types. Sensible defaults are given below.
+ */
+ #socks5_ports = 80, 443, 1080, 8000, 8080, 10800;
+
+ /* These are the ports to scan for HTTP CONNECT proxies on (plaintext).
+ * They may overlap with other scan types. Sensible defaults are given
+ * below.
+ */
+ #httpconnect_ports = 80, 8080, 8000;
+
+ /* These are the ports to scan for HTTPS CONNECT proxies on (SSL).
+ * They may overlap with other scan types. Sensible defaults are given
+ * below.
+ */
+ #httpsconnect_ports = 443, 4443;
+#};
+
/*
* Alias blocks allow you to define custom commands. (Old m_sshortcut.c)
* They send PRIVMSG to the given target. A real command takes
*/
default_floodcount = 10;
- /* failed oper notice: send a notice to all opers on the server when
+ /* failed oper notice: send a notice to all opers on the server when
* someone tries to OPER and uses the wrong password, host or ident.
*/
failed_oper_notice = yes;
/* dots in ident: the amount of '.' characters permitted in an ident
* reply before the user is rejected.
*/
- dots_in_ident=2;
+ dots_in_ident = 2;
/* min nonwildcard: the minimum non wildcard characters in k/d/g lines
* placed via the server. klines hand placed are exempt from limits.
* displayed unconditionally.
*/
global_snotices = yes;
-
- /* dline reason: show the user the dline reason when they connect
+
+ /* dline reason: show the user the dline reason when they connect
* and are dlined.
*/
dline_with_reason = yes;
-
- /* kline delay: delay the checking of klines until a specified time.
- * Useful if large kline lists are applied often to prevent the
- * server eating CPU.
- */
- kline_delay = 0 seconds;
- /* kline reason: show the user the reason why they are k/dlined
+ /* kline reason: show the user the reason why they are k/dlined
* on exit. may give away who set k/dline when set via tcm.
*/
kline_with_reason = yes;
+ /* tkline duration: when showing users their k/dline reason (see
+ * kline_with_reason), don't add "Temporary K-line 123 min."
+ */
+ hide_tkdline_duration = no;
+
/* kline reason: make the users quit message on channels this
* reason instead of the oper's reason.
*/
non_redundant_klines = yes;
/* warn no nline: warn opers about servers that try to connect but
- * we dont have a connect {} block for. Twits with misconfigured
+ * we dont have a connect {} block for. Twits with misconfigured
* servers can get really annoying with this enabled.
*/
warn_no_nline = yes;
stats_e_disabled = no;
/* stats c oper only: make stats c (connect {}) oper only */
- stats_c_oper_only=no;
+ stats_c_oper_only = no;
/* stats h oper only: make stats h (hub_mask/leaf_mask) oper only */
- stats_h_oper_only=no;
+ stats_h_oper_only = no;
/* stats y oper only: make stats y (class {}) oper only */
- stats_y_oper_only=no;
+ stats_y_oper_only = no;
/* stats o oper only: make stats o (opers) oper only */
- stats_o_oper_only=yes;
+ stats_o_oper_only = yes;
/* stats P oper only: make stats P (ports) oper only
- * NOTE: users doing stats P will never be given the ips that the
+ * NOTE: users doing stats P will never be given the ips that the
* server listens on, simply the ports.
*/
- stats_P_oper_only=no;
+ stats_P_oper_only = no;
/* stats i oper only: make stats i (auth {}) oper only. set to:
* yes: show users no auth blocks, made oper only.
* masked: show users first matching auth block
* no: show users all auth blocks.
*/
- stats_i_oper_only=masked;
+ stats_i_oper_only = masked;
/* stats k/K oper only: make stats k/K (klines) oper only. set to:
* yes: show users no auth blocks, made oper only
* masked: show users first matching auth block
* no: show users all auth blocks.
*/
- stats_k_oper_only=masked;
+ stats_k_oper_only = masked;
/* map oper only: make /map oper only */
map_oper_only = no;
/* REMOVE ME. The following line checks you've been reading. */
havent_read_conf = yes;
-
- /* max targets: the maximum amount of targets in a single
+
+ /* max targets: the maximum amount of targets in a single
* PRIVMSG/NOTICE. set to 999 NOT 0 for unlimited.
*/
max_targets = 4;
*
* +g - callerid - Server Side Ignore
* +D - deaf - Don't see channel messages
- * +i - invisible - Not shown in NAMES or WHO unless you share a
+ * +i - invisible - Not shown in NAMES or WHO unless you share a
* a channel
* +l - locops - See LOCOPS messages
* +Q - noforward - Unaffected by channel forwarding
* +w - wallop - See oper and server generated WALLOPS
* +z - operwall - See operwalls
*/
-
+
/* oper only umodes: usermodes only opers may set */
oper_only_umodes = operwall, locops, servnotice;
oper_snomask = "+s";
/* compression level: level of compression for compressed links between
- * servers.
+ * servers.
*
* values are between: 1 (least compression, fastest)
* and: 9 (most compression, slowest).
away_interval = 30;
/* certfp_method: the method that should be used for computing certificate fingerprints.
- * Acceptable options are sha1, sha256 and sha512. Networks running versions of charybdis
- * prior to charybdis 3.5 MUST use sha1 for certfp_method.
+ * Acceptable options are sha1, sha256, spki_sha256, sha512 and spki_sha512. Networks
+ * running versions of charybdis prior to charybdis 3.5 MUST use sha1 for certfp_method.
+ *
+ * The spki_* variants operate on the SubjectPublicKeyInfo of the certificate, which does
+ * not change unless the private key is changed. This allows the fingerprint to stay
+ * constant even if the certificate is reissued. These fingerprints will be prefixed with
+ * "SPKI:SHA2-256:" or "SPKI:SHA2-512:" depending on the hash type. These fingerprints
+ * are not supported on servers running charybdis 3.5.3 or earlier.
+ *
+ * To generate a fingerprint from a certificate file, please use the mkfingerprint utility
+ * program located in the bin/ subdirectory of your IRCd installation. Running it with no
+ * arguments will give you a brief usage message; it takes method and filename arguments.
*/
- certfp_method = sha1;
+ certfp_method = spki_sha256;
/* hide_opers_in_whois: if set to YES, then oper status will be hidden in /WHOIS output. */
hide_opers_in_whois = no;
};
modules {
- /* module path: paths to search for modules specified below and
+ /* module path: paths to search for modules specified below and
* in /modload.
*/
path = "/usr/local/ircd/modules";
projects / solanum.git / blobdiff